www.powersolve.co.uk
Powersolve Electronics Ltd. 8A, Arnhem Road, Newbury, RG14 5RU. England
AC-DC Converters
JB200 Redundant Series
200 Watts
Single Output
Switching Power Supply
Features
• Providing Peak Power of 600W within 500uS duty duration
• Compact 1U Height & Power Density: 5.16 watts/cu in
• Power factor corrected to EN61000-3-2 class A
• Approved to UL CUL TUV CB and CE
• AC input range auto-selectable
•
N+1 parallel redundancy
• Optional Top Cover
Input Voltage: 90-132 / 180-264Vac, 47-63HZ auto selectable.
Input Current: 5/2.5A at 115/230VAC.
Inrush Current: Max. 70A@230Vac & 35A@115Vac; cold start.
PFC: Power factor correction to EN61000-3-2 class A (total parallel output power not exceeding 200W).
Transient Response: Output voltage returns to within 1% in less than 2.5mS for a 50% load change, peak does not exceed 5%.
Overshoot: Turn-on & off overshoot < 5% over nominal voltage.
Efficiency: 70% for 3.3V, 75% for 5V, 80% for 12V and 83% minimum for other outputs @ 230V and full load.
Turn On Delay: 1 second maximum at 120 VAC.
Hold Up Time: 20mS min. at120Vac & 80% of full load.
Adjustability: Output user adjustable +/-5% minimum.
Input Fusing Protection: One T5A/250V fuse inserted in primary.
Over-Voltage Protection: Unit latches down when output exceeds 130% and recycle AC input to reset.
Over-Power Protection: Fold back mode 110-135%; Auto-recovery.
Short-Circuit Protection: Trip without damage and auto-recovery.
Over-Temperature Protection: Unit protected against excessive operating ambient of 85 °C, and automatic recovery.
Switching Frequency: 25KHZ fixed frequency.
Operating Temperature: 0 to 40 degrees C.
Storage Temperature: -20 to 85 degrees C.
Operating Humidity: 5% to 90% RH, Non-condensing.
Storage Humidity: 5% to 95% RH, Non-condensing.
Vibration: Frequency 5 to 50 Hz, acceleration +/-7.35 M/(SxS) on X,Y and Z Axis.
Remote On-Off: Designated as REMO on the CN3. Requires a low signal to inhabit output; Hiccough mode.
Power Supply On: Green LED designated as LED1 on the PCB.
Power Good: Designated as PG on the CN3 will go high 100-500 mS after regulation and goes low 1mS before loss of regulation.
Fan Drive: 12VDC/300 mA is available to drive an external fan.
EMC Standards: CISPR 22 / EN55022 class B, EN61000-3-2,3, EN61000-4-2,3,4,5,6,8,11, EN55024 CE Marked (LVD).
Safety Regulation: Approved to UL60950-1, CSA C22.2 No. 60950- 1, TUV EN60950-1 and CB certificate available.
Leakage Current: 1.5mA @ 240Vac.
HI-POT Test: 1500 VAC input line to chassis (10mA DC cut off current);
Isolating 3000VAC primary to secondary windings;
Primary to core 1500VAC. All for 3 sec.
Grounding Test: Apply 25 A from ground pin of the three prong plug to the far most earth. Max allowable resistance 0.1 ohm.
MTBF: 100000 Hrs (according to MIL-HBK-217F) at 30 degree C.
Cooling: 200W max. with 18.7cfm airflow or 150W max convection.
Enclosure: 6.8(L) x 3.8(W) x 1.5(H) inches; U-Chassis Type.
Weight: Maximum weight is 600g.
Electrical Specification
Overall Size: 6.8(L) x 3.8(W) x 1.5(H)inches
Comments to this Manuals